These fasteners provide a quick and neat method to attach bubble insulation, poly, or shade fabric to the inside of most alum...
About 2567 Spray Adhesive (B7567)
General Product Information:
High Strength Fast Tack Spray Adhesive is transparent and pressure sensitive. It provides instant tack, is repositionable, has a lace spray pattern and offers the user a low soak in with a high bond strength. This product is recommended for use on wood, polyurethane foam, fabrics, paper, dry wall, masonry, plastic, polyethylene and painted surfaces. It is compatible with most types of styrene board and will not degrade the substrate if sprayed from a distance of 12” to 15”.
This product does not contain:
Ozone depleting chemicals
Shake well before using. Clean object or surface thoroughly. Point valve toward surface and spray from a distance of 6 to 8 inches, keeping the can moving to avoid a buildup on the surface. Only a thin film is required. Avoid over spraying. Let adhesive dry to a tack before bonding. For a permanent bond, spray both surfaces, allow to tack, then bond. For a temporary or repositionable bond, spray one surface, allow to tack and apply.
Do to this product’s low soak-in characteristics and high “green strength,” it is especially recommended when bonding polyethylene film to drywall, brick, and concrete block. It is also excellent for use in partitioning and isolating construction areas.
Standard shipping charges apply.
Caution: Contains Acetone (CAS 67-64-1), Hexane (CAS 110-54-3), Propane (CAS 74-98-6), Dimethyl Ether (CAS 115-10-6) and NJTSRN 80100049-5003P (nonvolatile). Vapors will accumulate readily. Keep product away from heat, sparks, flames, and sources of static discharge. Do not store above 120° F, or in direct sunlight. Do not puncture, incinerate or discard in compactor.
Avoid contact with skin and eyes. Use directional arrow on spray head to avoid spraying in eyes. May cause eye, skin and respiratory tract irritation.
Overexposure to vapors may cause central nervous system depression resulting in symptoms such as lightheadedness, nausea and headache. It also may cause peripheral nervous system effects such as numbness in the extremities. Use with adequate ventilation, ensuring fresh air entry during application. If you experience symptoms of overexposure, increase fresh air or leave the area.
Effects of Overexposure:
Eye Contact: Can cause sever irritation, redness, tearing and blurred vision.
Skin Contact: Prolonged or repeated contact can cause moderate irritation.
Inhalation: Excessive inhalation of vapors can cause nasal and respiratory irritation, dizziness, weakness, fatigue, nausea, headache, possible unconsciousness, and even asphyxiation. Over exposure may cause damage to the nervous system.
In case of eye contact, flush with water for at least 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty provide fresh air and call physician immediately.
Harmful or fatal if swallowed. Do not induce vomiting. Call physician immediately.
Eye Contact: Flush with large amounts of water, lifting upper and lower lids occasionally, get medical attention.
Skin Contact: Thoroughly wash exposed area with soap and water. Remove contaminated clothing. Launder contaminated clothing before re-use. Get medical attention if irritation persists. Mineral oil, baby oil, makeup remover, mineral spirits, or other similar mild solvents may be used to remove the sticky resin residue left by the adhesive.
Inhalation: Remove individual to fresh air. If breathing is difficult, administer oxygen. Give artificial respiration if breathing has stopped. Keep person warm and quiet. Get medical attention.
Ingestion: Do not induce vomiting. Give two glasses of water if conscious. Never give anything by mouth to an unconscious person. Get immediate medical attention.
Not recommended for unsupported vinyl fabric. Certain plastic and elastomeric substrates can exhibit bond failure due to plasticizer migration. Combinations of high temperature and humidity can promote bond failure. For nonmetallic substrates, testing of production parts in typical operation environments for compatibility and performance is recommended.
Not for use on Polycarbonate.
For further information, please contact Charley's Customer Service at 1-800-322-4707.
Warranty: This item is backed by Charley's 100% guarantee. If you are not completely
satisfied, return your purchase in the condition you receive it, within
30 days, for a refund, exchange or credit - whichever you prefer. If any
product is found to be defective within the first year, it may be returned
or exchanged for full credit.